ASTM6584 Glycerin content by GC

From LEAP

(Difference between revisions)
Jump to: navigation, search
(LEAP's Approach)
Line 83: Line 83:
[[Image:6584.jpg|600px|Center|System shown with Agilent 7890 and Twin PAL]]
[[Image:6584.jpg|600px|Center|System shown with Agilent 7890 and Twin PAL]]
 +
 +
This digital application note describes a LEAP turn-key system for the analysis of free and total glycerines in biodiesel fuel.
                
                
LEAP uses a [http://www.leapwiki.com/mediawiki/index.php?title=TwinPAL Twin PAL] to solve this application due to the many different solvent, internal standard, and sample volumes required.
LEAP uses a [http://www.leapwiki.com/mediawiki/index.php?title=TwinPAL Twin PAL] to solve this application due to the many different solvent, internal standard, and sample volumes required.

Revision as of 18:41, 15 January 2010

Biofuels
Application Type
  Sample Prep and Inject
Application ID
  Biodiesel ASTM 6584
Description
  Determination of Free and Total Glycerin in B-100 Biodiesel Methyl Esters by Gas Chromatography
 ↳ leaptec.com  ↳ leapwiki.com

Contents

Overview

Glycerin content can indicate the quality of biodiesel. Glycerin can be in the form of free glycerin or bound glycerin in the form of glycerides. Total glycerin is the sum of these. A high or excessive content of free and total glycerin can lead to buildup in fuel tanks, clogged fuel systems, injector fouling and deposits on valves and pistons. Unrelated glycerides and free glycerin make the product behave more like soap rather than fuel.

ASTM Method D6751 specifications serve as the benchmark which identifies the standards that pure biodiesel (B100) must meet before being used as a fuel or blended with petrodiesel. There are 14 different required tests according to ASTM D6751-03. The US National Biodiesel Board has adopted the ASTM biodiesel specification and analytical methodology. ASTM recommends test method ASTM D6584 for the analysis of glycerin in biodiesel fuel by gas chromatography.

ASTM Method D6584 provides for the quantitative determination of free and total glycerin in B-100 methyl esters by gas chromatography. The range of detection for free glycerin is 0.005 to 0.05 mass%, and total glycerin from 0.05 to 0.5 mass %. This method is not applicable to vegetable oil methyl esters obtained from lauric oils, such as coconut oil and palmkernel oil. ASTM Method D6584 deals with expensive and toxic reagents and requires very complex and time consuming procedures for preparing calibration standards and finished B100 biodiesel. Manual standards and sample preparation remains a tedious chore that can significantly contribute to errors and lost precision in the GC analysis. Automation can help with all of these.

Gas chromatography (GC) is ideal for measuring important parameters such as total glycerin, fatty acid methyl esters (FAMEs) and methanol levels in biodiesel fuel. Methods like ASTM D-6584 and EN14105 are the standards for testing total glycerin and glycerides in biodiesel oil.

Gas chromatography (GC) can also serve as a tool for process troubleshooting during biodiesel production to ensure trouble-free operation of the fuel in diesel engines. Monitoring the level of free glycerin and any unrelated mono-, di-, and triglycerides will indicate the efficiency and progress of the chemical reaction during the process of making biodiesel.

Significant Markets

  • Biodiesel Manufactures
  • Biodiesel Blenders
  • Biodiesel Distributors
  • Biofuels CROs
  • Fleet Managers



ASTM Method D6584

9. Calibration and Standardization

9.2 Standard Solutions – Prepare the five standard solutions in Table 3 by transferring the specified volumes by means of microliter syringes to 10mL septa vials

TABLE 3 Standard Solutions
Standard Solution Number 1 2 3 4 5
uL of glycerin stock solution 10 30 50 70 100
uL of monoolein stock solution 20 50 100 150 200
uL of diolein stock solution 10 20 40 70 100
uL of triolein stock solution 10 20 40 70 100
uL of butanetriol stock solution 100 100 100 100 100
uL of tricaprin stock solution 100 100 100 100 100

9.4 Standardization
9.5 Inject 1 uL of the reaction mixture into the on-column injection port and start the analysis.


10. Procedure
10.1 Weigh to the nearest 0.1 mg approximately 100 mg of sample directly into a 10 mL septa vial.

10.2 Inject 1 uL of the reaction mixture into the on-column injection port and start the analysis.


LEAP's Approach

System shown with Agilent 7890 and Twin PAL

This digital application note describes a LEAP turn-key system for the analysis of free and total glycerines in biodiesel fuel.

LEAP uses a Twin PAL to solve this application due to the many different solvent, internal standard, and sample volumes required.

The Lower PAL is the Prep PAL and runs on Cycle Composer Software. All of the sample prep is performed with this PAL. There is a 100ul syringe for the solvent transfers. There are (7) 2mL solvent locations. There is a DISPTool that is hooked up to a 5 mL dilutor syringe for the 8 mL Heptane addition. There is a wash station for the through cleaning of the syringe that has two wash solvents. Wash1 is filled with Toluene and Wash 2 is filled with Heptane. There is an agitator that is set at 35 deg C and 500RPM to do the mixing.

The Upper PAL is the Inject PAL and runs under ChemStation Software control using the Agilent CTC Control Software. It is using a 5 ul syringe with a tapered needle to do 1 ul on column injection into the rear injection port. There is a wash station for the through cleaning of the syringe]that has Wash1 is filled with Toluene and Wash 2 is filled with Heptane.

The expected Sample Prep Time is approximately 26 minutes
The expected GC Runtime is approximately 31.81 minutes
The expected GC Cool down time is approximately 7 minutes



Software Control

The Lower PAL is the Prep PAL and runs on Cycle Composer Software.

The Upper PAL is the Inject PAL and runs under Agilent ChemStation control.


This process can be done on other GC's and data systems and does not require the Agilent approach.

Also, LEAP now has the ability use the new Chronos Software as it organizes parallel processes for sample preparation. This utilizes the analysis system to a much greater extent, while observing the time margins of each individual sample preparation. There is a single sample list for the entire process and integrates well with Xcalibur from Thermo Scientific and ChemStation from Agilent .

Screenshots

Video

Dispense tool in action on youtube


Useful links

ASTM.ORG

An overview of all tests that must be run by Piedmont Biofuels

A good general reference site by Agilent

UCONN.com A good general reference site on Biodiesel ASTM Methods

A good general reference site on Biodiesel

Biodiesel Plant Listing

Biodiesel Conference 2009

Biodiesel Confernece 2010

NREL B100


More Info

To get to the main LEAP digital brochure for other applications: LEAP Wiki Main Page

Info on EN 14110 Methanol content by HS

Info on ASTM D 5453 Sulfur Content

More info on the TWIN PAL
More info on LEAP Accessories
More info on Large Volume Dispensing
More info on Washing the Syringe
More info on Shaking and Agitation
More info on the Dilutor
More info on On-Column
More info on Reagent Storage
More info on the PAL


 ↳ leaptec.com  ↳ leapwiki.com

LEAP provides automated workstation instrumentation solutions based on the LEAP CTC PAL X, Y, Z syringe only autosampler robot from LEAP Technologies. This extremely flexible, precise, and adaptable liquid handling robotic platform is available in a variety of lengths and options depending on the requirements of your sample preparation and injections for your UHPLC, LC or GC chromatography.LEAP offers full support and service for the PAL platform in addition to being able to write custom macros, cycles, and scheduling to your applications. Please contact LEAP Technologies on how we can help you get maximized throughput with flexible pipetting automation solutions.

Contact LEAP

Contact LEAP

For additional information about the PAL and the application, please contact LEAP Technologies.

Keywords

biodiesel, free glycerin, gas chromatography, methyl esters, total glycerin

Personal tools