Large Volume Dispensing
From LEAP
(→Dilutor Accessory) |
|||
| Line 25: | Line 25: | ||
=== Dilutor Accessory === | === Dilutor Accessory === | ||
| + | Can feed a solvent through the injection syringe into sample plates or vials | ||
| + | <br> | ||
| + | There are multiple options on the PAL for delivery of volumes of solvent. Choice will depend on the requirements for delivery rate, delivery volume and accuracy. | ||
| + | === Dilutor Accessory === | ||
| + | Syringe pump volume range of 0.25 ml to 2.5ml delivery per 2.5 ml syringe cycle. (Optional dilutor syringe 1ml or 5 ml)<br> | ||
| + | Flow Rate Range: 10μl/min - 300μl/min<br> | ||
| + | Wetted parts: All liquids compatible with borosilicate glass, PTFE, Kel-F, FEP | ||
| + | <br> | ||
| + | === Can be used for === | ||
| + | * Sample Derivations | ||
| + | * Sample Dilutions | ||
| + | * Standard Additions | ||
| + | * Accelerated Wash Step in HTS applications | ||
| + | <br> | ||
| + | ''' Notes ''' | ||
| + | * Requires the addition of a custom macro or cycle for dispensing/diluting applications | ||
| + | * Can be used with any of the PAL side port syringes or with the DISPENSE Tool | ||
| + | * Is not supported by the on board PAL cycles | ||
| + | * Requires an open AUX Port on the PAL | ||
| + | * Requires PAL firmware 2.3 or higher | ||
Syringe pump volume range of 0.25 ml to 2.5ml delivery per 2.5 ml syringe cycle. (Optional dilutor syringe 1ml or 5 ml)<br> | Syringe pump volume range of 0.25 ml to 2.5ml delivery per 2.5 ml syringe cycle. (Optional dilutor syringe 1ml or 5 ml)<br> | ||
Flow Rate Range: 10μl/min - 300μl/min<br> | Flow Rate Range: 10μl/min - 300μl/min<br> | ||
Revision as of 14:45, 7 October 2009
| Large Volume Dispensing |
| Application Type | |
| SPECIAL | |
| Application ID | |
| Description | |
| Accurate dispensing of solvents at high flow rates |
Contents |
Overview
There are three options on the PAL for delivery of large volumes of solvent. Choice will depend on the requirements for delivery rate, delivery volume and accuracy. In each case these pumps can dispense liquid either through PAL side-port syringe, or using the LEAP "Dispense Tool" accessory. The advantage of the latter is that it permits larger flow rates and includes a venting channel to avoid over pressurization in the case of filling sealed vessels.
Common Uses
- Dispense liquid prior sample injection and combines the "add liquid" and "inject" steps without user intervention or syringe change.
Typical applications
- Dilutions
- Derivatisations
- Sample spiking
- Standard additions
Dilutor Accessory
Can feed a solvent through the injection syringe into sample plates or vials
There are multiple options on the PAL for delivery of volumes of solvent. Choice will depend on the requirements for delivery rate, delivery volume and accuracy.
Dilutor Accessory
Syringe pump volume range of 0.25 ml to 2.5ml delivery per 2.5 ml syringe cycle. (Optional dilutor syringe 1ml or 5 ml)
Flow Rate Range: 10μl/min - 300μl/min
Wetted parts: All liquids compatible with borosilicate glass, PTFE, Kel-F, FEP
Can be used for
- Sample Derivations
- Sample Dilutions
- Standard Additions
- Accelerated Wash Step in HTS applications
Notes
- Requires the addition of a custom macro or cycle for dispensing/diluting applications
- Can be used with any of the PAL side port syringes or with the DISPENSE Tool
- Is not supported by the on board PAL cycles
- Requires an open AUX Port on the PAL
- Requires PAL firmware 2.3 or higher
Syringe pump volume range of 0.25 ml to 2.5ml delivery per 2.5 ml syringe cycle. (Optional dilutor syringe 1ml or 5 ml)
Flow Rate Range: 10μl/min - 300μl/min
Wetted parts: All liquids compatible with borosilicate glass, PTFE, Kel-F, FEP
Notes
- Requires the addition of a custom macro or cycle for dispensing/diluting applications
- Can be used with any of the PAL side port syringes or with the DISPENSE Tool
- Is not supported by the on board PAL cycles
- Requires an open AUX Port on the PAL
- Requires PAL firmware 2.3 or higher
 Dilutor with DISPTool |
 Dilutor on PAL |
Mini Pump Series Accessory
The Mini Pump liquid handling pump is a syringe-free pump capable of delivering a bidirectional flow to six orders of magnitude. The Mini Pump is a positive displacement pump, which means that it is self-priming and tolerant of any gas which may find its way into the fluid lines. Since there is no separate fill cycle, the pump can be operated continuously, and volumetric capacity is limited only by time.
Notes
- Requires LEAP Shell Software for control.
- Can be used with any of the PAL side port syringes or with the DISPENSE Tool
- Is not supported by the onboard PAL cycles
 Mini Pump |
Pump on PAL |
Solvent Delivery System (SDS) Accessory
Main Features
- 4 Solvents can be dispensed
- 9 Program Steps allow solvents to be added in any order
- Software Interface SDS Launchpad for loading dispense routines
- Save/Load Methods to PC drive
- Easy Verification of Downloaded Method via the “Dashboard” feature in SDS Launchpad
- Contact closure triggers device to run stored dispense routine
- Significantly extends the PAL dispenseing volume range.
- Can be used with any PAL side port syringe or LEAP DISPENSE Tool
- Compatible with all PAL Drivers
 Solvent Delivery Module |
 SDS on PAL |
Performance Specifications
- Maximum flowrate 6mL/min in increments of 0.1mL/min
- Flowrate accuracy ± 10%
- Maximum dispensed volume 999mL
- Volumetric accuracy ± 5%
- Maximum pressure 50PSIG
- Typical wash time for 2 solvents (1mL each) @ 6mL/min is 45 seconds
Requirements/Limitations
- Lower dispense speeds needed for more viscous solvents, e.g., i-Propanol @ 3-4mL/min
- Use of Polypropylene compatible solvents
Screenshots
 Launch Pad Main Screen |
 Launch Pad Actions Screen |
 Launch Pad Load Method Screen |
 Launch Pad Log Screen |
Side Port Syringe Accessory
Main Features
- Can be used to dispense liquid prior sample injection
- Combines the "add liquid" and "inject" steps without user intervention or syringe change
- Variety of sizes available: 20µl or 80µl for LC applications and 20µl or 80µl for GC applications
 Side Port Syringe in action |
 Side Port on PAL |
Side Port on PAL |
DISPTool Accessory
Main Features
- Can be used to dispense bulk liquids without using the injection syringe
- The tool is magnetically picked up by the PAL and moved to the vial or plate only when needed
- Able to pierce a septa with an adjustable needle penetration
- 19ga needle with built in vent
- May allow single rail to have functionality of dual rail system
- Can be used with the Dilutor, Mini Pump, or LEAP SDS
Requirements/Limitations
- Requires some additional rail space for DISPTool parking location
- Requires custom firmware
|
 |
 |
Video
Dispense Tool movement Uses Windows Media Player to view
Dispense tool in action on youtube
Various PAL's in action on YouTube
PRINT Function for Page
PDF of this page formatted for printing
LEAP strives to find total solutions for analytical lab automation by automating analytical processes for small and large molecules in extracted liquids, solids, and recently in human, animal and plant tissues. We provide the precise robotics and efficient sample prep required by modern measurement techniques such as MALDITOF mass spectroscopy. Our newest specialty customization of CTC Analytics’ PAL features small workstations that can perform complex liquid handling tasks including HPLC-Purification, SPE, filtration, weighing, heating and stirring. They can be configured as stand alone units or integrated for “just in time” sample prep for LC-MS or GC-MS analysis.
LEAP provides automated workstation instrumentation solutions based on the LEAP CTC PAL X, Y, Z syringe only autosampler robot from LEAP Technologies. This extremely flexible, precise, and adaptable liquid handling robotic platform is available in a variety of lengths and options depending on the requirements of your sample preparation and injections for your UHPLC, LC or GC chromatography.LEAP offers full support and service for the PAL platform in addition to being able to write custom macros, cycles, and scheduling to your applications. Please contact LEAP Technologies on how we can help you get maximized throughput with flexible pipetting automation solutions.
Contact LEAP
 Contact LEAP
For additional information about LEAP and the PAL Platform, please contact LEAP Technologies. |
